Suntan Special version 0.66
Suntan Special DVD edition
Warp 4 Convenience Pack (MCP)
Merlin Convenience Pack (MCP) is IBM's OS/2 Warp 4 with all
fixes applied. First released in November 2000, the software runs
on Intel personal computers. This version of the installation
has been created especially for use with Suntan Special.
Merlin Convenience Pack comes on two (2) CD-Roms. I refer to these
CD-Roms as the Boot CD and the Install CD.
- Boot the computer from the Boot CD. The first screen tells you to
insert the Install CD. Do so and press Enter. The program will load from
the Install CD and the Welcome Screen will appear.
- If anything needs to be prepared on the computer, this is a good time
to do it. You may access a full screen command window by pressing F3. If
you do so, type "exit" and press Enter to return to the Welcome Screen.
Otherwise, press Enter to go on.
- The OS/2 Warp Installation screen will appear. Press Enter to go
- The Installation Volume Selection screen will appear. Unless it
already has the correct volume specified, select "2. Specify a different
volume" and press Enter.
- The Modifying Volumes Warning screen will appear. Press Enter to
dismiss this warning.
- The Partition Table corrupt screen may appear. It did on my system
because I have an internal zip drive. This warning usually can be
ignored. Press Enter to dismiss this warning.
- The System is not able to use this disk message may appear. This
warning accompanies the previous warning on my system. It is probably
referring to the zip disk. This warning can be ignored. Press Enter to
dismiss the warning.
- The next screen explains that a volume of the following size must be
set installable. Note the size when selecting a volume for installation.
The minimum size is much too small for a proper Suntan Special
installation volume. Be generous if possible with the installation
partition. I like to provide 3 Gb as a volume size, but that is to allow
the applications to also reside on the installation volume. Press Enter
to go on.
- The Logical Volume Manager screen now appears. If the volume you wish
to use as the installation volume already exists, select it, and press
Enter. Otherwise, create the volume, select it and press Enter.
- Select the menu option to set the volume installable, and press Enter.
Then press the F3 key to exit. Select "Save changes and Exit" and press
- The Installation Volume Selection screen will appear again, but this
time with the appropriate volume selected. Select "1. Accept the Volume"
and press Enter.
- The Formatting the Installation Volume screen will appear. If this is
a newly created volume, then a long format would be appropriate. If this
is an existing volume, then a quick format is probably enough. Unless a
long format will make you feel more secure, select "3. Perform a Quick
Format" and press Enter.
- The Select a File System screen will appear. Do not even consider
FAT. Select "1. HPFS" and press Enter.
- The Attention: volume may contain data screen will appear, even if the
volume definately does not contain data. This is the last installation
screen for a while. When you press Enter, the installation program will
format the installation volume, copy a lot of files to it, and then reboot
- When the computer restarts, the display will be handled by
Presentation Manager, and the windows will be the familiar OS/2 GUI. The
System Configuration screen will appear. Set the Primary Display to VGA,
the CD-ROM Device support to IDE-CDROM, and the Multimedia Device support
to None. When the selections are correct, press the Next button.
- The System Configuration (cont.) screen will appear. Make sure APM is
enabled (unless your computer does not support APM, which is unlikely,)
then press Next.
- The Country selection screen will appear. Select the appropriate
country and press Next.
- The Select System Default Printer screen will appear. Select Do not
select a default printer and press Next.
- The Options screen will appear. Most of the selections can be left to
their default values. However, press the System Utilities button and
ensure that all options are selected. Also, press the Tools and Games
button and select Optional Bitmaps. Press next to continue.
- The Installing OS/2 Warp 4 screen will appear. Press Next.
- The information screen will appear. Fill in all of the information.
On my system, it was filled in already. I do not know how it does
this. Press Next.
- The select services to install screen will appear. I left everything
in its default state. Press Next.
- The configuration screen will appear. This is a screen with a tree of
options on the left and a frame with specific parameters for each option
on the right. There are a number of tasks to complete on this page. The
tasks will be completed from the bottom of the screen and working up to
the top. The items on this list make sense only if you have a network
- Click the Network Adapters and Protocol Services icon on the tree. At
this time, insert the diskette containing your network adapter driver, or
be sure of the exact location on the hard drive. Click on Other Adapter,
set the location, and let the program copy the driver files. If you have
more than one Network Adapter, you will need to repeat the process.
- Select the TCP/IP Services icon on the tree. Select DHCP Server on
LAN if you have that, otherwise fill in the following fields on the right
hand side. TCP/IP address is the address for your first (or only) network
card. Subnet mask is the mask for your LAN (most commonly 255.255.255.0)
The router is the IP address of your router or gateway. The hostname is
the name of this computer for TCP/IP purposes. I try to use the same name
for TCP/IP and NetBIOS. Leave the rest blank.
- Select the Username and Password icon on the tree. Fill in the user
name and password for NetBIOS networking.
- Select the File and Print Client icon on the tree. Fill in the
Workstation name, the Description and the Workgroup name.
- You may click the other icons and look at the values, but nothing else
needs to be configured. Press the Install button.
- The configuration screen will appear. Press OK to start the
installation. The installation will continue for some time, and will
restart the computer.
- The computer will restart with the Workplace shell. The Java 1.3
Install screen will appear. Select No. If you have MCP, you also have a
more recent version of Java, which should be installed instead. The
installation of MCP is now complete.
- This is a good time to make a backup of the installation. I usually
have backup software on another boot partition, and I will use it at this
The resulting installation consumes 241.4 Mb according to my backup
software, Back Again/2000.
Last Modified: 29 Jan 2017
Graphics by Colorful Language
Copyright 2017 by Blonde Guy